Iver Johnson M1 Carbine 100% Stainless Steel, almost impossible to find in Stainless and in good condition, plus the original factory leather sling. This is a handy light weight good feeling fun to shoot, a hunting brush gun with very little recoil and cheap ammo. Manufactured in 1982 or 83 by Iver Johnson Arms in Middlesex, New Jersey, you can check the serial number.
Prior to World War II, U.S. Army Ordnance received reports that the full-size M1 rifle
was too heavy and cumbersome for most support troops (staff, mortarmen, radiomen, etc.) to carry. During prewar and early war field exercises, it was found that the M1 Garand impeded these soldiers' mobility, as a slung rifle would frequently catch on brush, bang the helmet, or tilt over the eyes. Many soldiers found the rifle slid off the shoulder unless slung diagonally across the back, where it prevented the wearing of standard field packs and haversacks. Additionally, Germany's use of glider-borne and paratroop forces to launch surprise ‘blitzkrieg’ attacks behind the front lines generated a request for a new compact infantry weapon to equip support troops. This request called for a compact, lightweight defensive weapon with greater range, accuracy and firepower than handguns, while weighing half as much as the Thompson submachine gun
or the M1 rifle
The U.S. Army decided that a carbine would adequately fulfill all of these requirements, but specified that the new arm should weigh no more than five pounds and have an effective range of 300 yards. Paratroopers were also added to the list of intended users and a folding-stock version would also be developed. In 1938, the Chief of Infantry requested that the Ordnance Department develop a "light rifle" or carbine, though the formal requirement for the weapon type was not approved until 1940. This led to a competition in 1941 by major U.S. firearm companies and designers. Winchester
at first did not submit a carbine design, as it was occupied in developing the .30-06 Winchester M2 Military Rifle. The rifle originated as a design by Jonathan "Ed" Browning, brother of the famous firearm designer John Browning
. A couple of months after Ed Browning's death in May 1939, Winchester hired David Marshall "Carbine" Williams
who had begun work on a short-stroke gas piston
design while serving a prison sentence at a North Carolina minimum-security work farm. Winchester, after Williams' release, had hired Williams on the strength of recommendations of firearms industry leaders and hoped Williams would be able to complete various designs left unfinished by Ed Browning, including the Winchester .30-06 M2 rifle. Williams incorporated his short-stroke piston in the existing design. After the Marine Corps
semi-automatic rifle trials in 1940, Browning's rear-locking tilting bolt design proved unreliable in sandy conditions. As a result, the rifle was redesigned to incorporate a Garand-style rotating bolt
and operating rod, retaining Williams' short-stroke piston. By May 1941, Williams had shaved the M2 rifle prototype from about 9.5 lb to a mere 7.5 lb. Ordnance found unsatisfactory the first series of prototype carbines submitted by several firearms companies and some independent designers. 
Winchester had contacted the Ordnance Corps to examine their rifle M2 design. Major René Studler of Ordnance believed the rifle design could be scaled down to a carbine which would weigh 4.5 to 4.75 lb and demanded a prototype as soon as possible. The first model was developed at Winchester in 13 days by William C. Roemer, Fred Humeston and three other Winchester engineers under supervision of Edwin Pugsley, and was essentially Williams' last version of the .30-06 M2 scaled down to the .30 SL cartridge. This patchwork prototype was cobbled together using the trigger housing and lockwork of a Winchester M1905 rifle and a modified Garand operating rod. The prototype was an immediate hit with army observers. After the initial army testing in August 1941, the Winchester design team set out to develop a more refined version. Williams participated in the finishing of this prototype. The second prototype competed successfully against all remaining carbine candidates in September 1941, and Winchester was notified of their success the very next month. Standardization as the M1 Carbine was approved on October 22, 1941. This story was the loose basis for the 1952 movie Carbine Williams
starring James Stewart
. Contrary to the movie, Williams had little to do with the carbine's development, with the exception of his short-stroke gas piston design. Williams worked on his own design apart from the other Winchester staff, but it was not ready for testing until December 1941, two months after the Winchester M1 Carbine had been adopted and type-classified. Winchester supervisor Edwin Pugsley conceded that Williams' final design was "an advance on the one that was accepted", but noted that Williams' decision to go it alone was a distinct impediment to the project, and Williams' additional design features were not incorporated into M1 production. In a 1951 memo written in fear of a patent infringement lawsuit by Williams, Winchester noted his patent for the short-stroke piston may have been improperly granted as a previous patent covering the same principle of operation was overlooked by the patent office. In 1973 the senior technical editor at the NRA contacted Edwin Pugsley for "a technical last testament" on M1 carbine history shortly before his death 19 Nov 1975. According to Pugsley, "The carbine was invented by no single man," but was the result of a team effort including Bill Roemer, Marsh Williams, Fred Humeston, Cliff Warner, at least three other Winchester engineers, and Pugsley himself. Ideas were taken and modified from the Winchester M2 Browning rifle (Williams' gas system), the Winchester 1905 rifle (fire control group), M1 Garand (buttstock dimensions and bolt and operating slide principles), and a percussion shotgun in Pugsley's collection (hook breech and barrel band assembly/disassembly).
No text messages or emails so call richard at 281-222-0808
What do you have to trade?????
Number of Times Viewed: 2689